Analog Communication Node
The Analog Communication Node is a device that enables all connected sensors (originally wired) for wireless LoRaWAN communication. The Analog Node is compatible with most of the analogue interfaces used for geotechnical sensors. Once the geotechnical sensors are connected to the Analog Node and the Gateways are correctly installed on-site, they are ready to receive, store and send data. You can freely configure the Analog Node and all the sensors connected remotely using the Move Cloud Platform. Perfect for implementing any monitoring system and meeting all project requirements.
The Analog Communication Node is a wireless device that enables all connected sensors (originally wired) for wireless LoRaWAN communication. The Analog Node has a maximum of 4 channels supported and it is compatible with most of the analogue interfaces used for geotechnical sensors.
The Analog Communication Node transmits accurate readings from all sensors connected via the LoRaWAN wireless communication protocol to the Gateway. You can freely configure the Analog Node and all the sensors connected remotely using the Move Cloud Platform. With this Platform, you can view and interact with your data online. Ideal for implementing any monitoring system and meeting all project requirements.
- A wireless device with built-in long-life battery
- Enables to LoRaWAN wireless communication any wired sensor
- 4 channels of sensors supported
- The sample rate can be set remotely
- Support Current Loop Reading (4-20mA) (2, 3, 4 wires)
- Support Full Bridge Reading (mV / V)
- Support PT-100 (3, 4 wires)
- ADC: 24bit Delta-Sigma with self-calibration
- Extremely easy installation with versatile mounting options
- Waterproof rating IP67
Some of the geotechnical sensors and probes with analogue interface compatible with the Analog Communication Node:
- Temperature sensor
- Inclinometer probes
- Pressure cell
- Load cell
- Rain gauge
- Radar level probe
|N° of sensors supported:||4 channels|
|Sample rate:||2 min - 10 min - 30 min - 1 hour (can be set remotely)|
|Power supply for external instruments:||5Vdc, 12vdc, 24Vdc (250mA max)|
|Readings supported:||• Current Loop Reading (4-20mA) (2, 3, 4 wires)
• Full Bridge Reading (mV / V)
• NTC and PTC reading (PT-100, PT-1000) (3, 4 wires)
|Supply:||2 Lithium battery 3.6V (19Ah)|
|Voltage reading accuracy:||±0.05% FS (±10Vdc)|
|Current loop reading accuracy:||±0.05% FS|
|Reading accuracy mV/V:||±0.1% FS|
|Thermistor reading accuracy:||±0.5°C|
|PT-100 reading accuracy:||±0.2°C|
|Wireless communication system:||LoRaWAN|
|Wireless coverage:||15 km (line of sight), 1 km (urban environment)|
|Processor:||ARM Cortex M4|
|Clock:||RTC On-Board (Real Time Clock) and high precision|
|Absolute synchronization:||±1 sec|
|ADC:||24bit Delta-Sigma with self-calibration|
|Size case:||180x119x61 mm|
|Operating temperature:||-40°C - 85°C|
|Operating temperature:||0.75 Kg|
|Input cable section:||24 - 20 AWG (Ø 0,5mm - Ø 0,8mm)|
|Method:||Pole or wall mounting using special plates and screws|
|Configuration:||- Pole fixing
- Mesh fixing
- Wall fixing
- Ceiling fixing
- Floor fixing
Easy installation of the Move wireless monitoring system
The installation of an entire wireless sensor system on site is quick and easy: simply mount each device with at least two screws on the structure you want to monitor and power the LoRaWAN Gateway. You can configure the entire system remotely, before, during or after installation, using your laptop or tablet. After assembly and setup, the Move wireless monitoring system will start measuring and you can start monitoring remotely.
Operation of the Move wireless monitoring system
The wireless sensor system automatically communicates the measurement data via LoRaWAN with the on-site Gateway which in turn sends the received data via 4G or LTE to the online servers. The Move Cloud Platform is the cloud-based web tool that allows you to access, view and export your measurement data and configure the settings of the entire sensor system. You can access the Move Cloud Platform 24/7 from any location or device around the world. One of the main advantages of the Move Cloud Platform is that it offers remote access to measurement data and allows remote configuration of all installed sensors. This saves time and labor. In addition, you can analyze the measurement data using processing algorithms included in the service. Perform complex calculations, correlations and analyzes automatically and effortlessly. With the touch of a button, you can export measurement data in CSV format. You can also easily configure alerts to multiple recipients who will receive threshold cross notifications via email.
- Easily install the entire system on the structure without the use of wiring.
- Configure all wireless sensors quickly and remotely.
- View real-time measurement data wherever you are, on any device, 24/7.
- Process the data collected through the implemented algorithms.
- Constantly monitors the operating status and signal quality of the system remotely.
- Customize your alarm notifications and receive overrun notifications by email.
- Optionally, you can integrate data on your platform using an MQTT bridge, FTP or through API calls.